[ OP-SB89 series comparison table ]
Model OP-SB89G OP-SB89E OP-SB89
Measurement port Port A and B
Monitoring 1CH of Ethernet communciation or PoE
Port A, B, C, and D
Monitoring 2CH of Ethernet communciation simultaneously
Port A and B: Monitoring 1CH of Ethernet communciation or PoE
Port C acts pseudo-PD port of class A or for cable testing.
Interface 10Base-T / 100Base-TX / 1000BASE-T 10Base-T / 100Base-TX
Fail-safe tap circuit*1 Between port A and B Between port A and B, port C and D Between port A and B
Monitor function*2 Measures Ethernet frames and record them. Measures Ethernet frames and record them.*3
Time Stamp 13 digits, minimum resolution: 40ns 13 digits, minimum resolution: 1µs
Recordable frames*4 Max. 48,000 to 1,048,000 frames (equivalent to max.100Mbyte) Max. 48,000 to 1,388,000 frames (equivalent to max.100Mbyte)
Suitable frame size 60 to 9Kbyte 60 to 2047byte
Translatable protocols IPv4, ARP, ICMP, TCP, UDP, and DHCP IPv4, ARP, ICMP, TCP, UDP, DHCP, and EtherCAT IPv4, ARP, ICMP, TCP, UDP, and DHCP
Trigger Level match with an external input or detection of a specified frame
It can stop measurement by the trigger.
Level match with an external input
It can stop measurement by the trigger.
Filter function You can monitor only the specified frame by filtering.
Search function It searches and counts only the specified frames.
Auto save function It can automatically records measured data into the external storage media as a communciation log file. It can automatically records measured data into the external storage media as a communciation log file.iOnly when it runs in REPEAT mode.)
Utility software A software to convert the log file into pcap format is provided. Supported OSFWindows 7/8/8.1/10
PG function It can output arbitrary packets in wire rate from the port A. It can output arbitrary packets in wire rate from the port A or port B. -
You can transmit up to 16 kinds of packets for the specified times or continuously.
A frame gap can be set for each packet.
Delay time measurement function - Measures the time lag between the receiving timings of specified ports in µs unit.(Current, Max, Min, and Average delay times are displayed.) -
Statistic function This function keeps statistics of 2 kinds of frame counters by specified interval (0 to 240 minutes), and display it in a graph.
All the frame counter values can be displayed in real time.
PoE measurement Measurement and continuous logging of the power consumption / Voltage / Current / Power (Alternative A/B, power supply port, polarity), OK/NG statement between devices of PoE (IEEE802.3af) / PoE+ (IEEE802.3at).
Interval: 1ms-1s. Max recording time: 400 million.
Voltage: 0-60V (}1% F.S.).
Current: 0-600mA (}2% F.S.).
- Measurement and continuous logging of the power consumption / Voltage / Current / Power (Alternative A/B, power supply port, polarity), OK/NG statement between devices of PoE (IEEE802.3af).
Interval: 1ms-1s. Max recording time: 400 million.
Voltage: 0-60V (}1% F.S.).
Current: 0-380mA (}2% F.S.).
PSE detection - Detect the PSE connection to the Port C and light the LED.
Cable test function - Measures the cable length (3-120m), or detects a short circuit and split pair.
PING function Transmits the PING commands and displays the response.
Port blink function It makes blink periodically the link LED of the HUB connected with the board.
Accessories Interface expansion board, line state sheet, LAN cable, Utility CD
*1It does not affect the communication between the devices even though the power of analyzer is turned off.
*2 Some capturing leakage may occuur when monitoring the communication on the high load network.
*3 It works by ONLINE mode (automatically stops measurement when the memory turns to be full) or REPEAR mode (continuous recoding).
*4 The frames are recorded with the additional data.

Close