Firmware Version History for LE-8200

Support sampling speed up to 100MHz in the Wave Monitor function.
Add precessing speed (minute, second) in the TREND function.
Support output and save the measured data in Text format. Furthermore, you can use the measured data in the calculation software etc.
Support Bit sequence at LSB First (SPI protocol) when using TTL/I2C/SPI expansion board (OP-SB85).
Able to transmit data when Clock phase is “0” without SS signal at SPI simulation.
Set back the SDO signal to be “1” when there is a rising edge of SS signal or another clock after transmission of the last bit at SPI Slave simulation.
Correct the bug of data missing after transmitting 3.7Mbps or more data at ASYNC communication.

Able to measure the HDLC/SDLC data of Manchester code.
Correct the bug of mis-counting the date of timestamp when measuring data for a couple months.
Correct the bug of auto-saving. When there is not enough capacity in the CF card, there will be some corrupt auto-saving files and become error.
Correct the bug that analyzer cannot measure frames when HDLC/SDLC starting flag is also used as ending flag.
Correct the bug that configuration speed of RD is applied to the SD speed, when setting the STS clock at the DCE simulation.
Correct the bug that analyzer measure data in duplicate when full duplex.
Correct the guide message in Enlighsh. "1:Stop" is changed to "1:Count" at "Action" of the Data Retrieval function.

Add the function which makes the external triger output active.
Add the settings for "OP-SB85L" in the "INTERFACE" setting menu.
Add the speed of 50Kbps, 200Kbps, 417Kbps for I2C master simulation.
Correct the bug of incomplete bit in the SPI slave simulation.
Change the beginning point to start the SPI slave simulation repeat mode as CS falling.
Improve the ability when receiving the large amount of data.
Correct the bug of Flow Simulation Send mode.
Support high speed access to the CF card.
Add the inter lock for starting measurement when TTL/IrDA pots are not connected.
Strengthen the self-check function.
Correct the miner bug of firmware loader.

Display frame for each timestamp in the new line when ASYNC protocol.
Create a new setting, "ASYNC frame NL" in the Display Control for above condition.
Change the guide message of "Line state" in the Display Control.
Support "print out" function for displaying timestamp between two frames when HDLC/PPP protocol.
Add the continuous display of analog waveform when using OP-SB85, OP-SB85IR or OP-SB85C.
(real time waveform while measuring which is similar to the oscilloscopes.)
Add slow sampling clock for analog waveform function.)
( Add 2us, 5us, 10us, 20us, 50us, 100us, 200us, 500us, 1ms )
Change the position when increasing/decreasing the waveform of analog/logic analyzer display.
Correct a miner bug of position of cursor/ marker for logic analyzer display.
Correct a miner bug of I2C translation display.(when using OP-SB85)
Add a function to communicate with PC efficiently by compressing the simulation program.
Correct a problem of "Invert"(Interface configuration) for simulation.
Correct the remote processing for unexpected command/ data.
Add a fuction not to freeze when receiving a large amount data.

Add the function of User defined translation function in which users can translate frame data at specified position to the characters or numbers.
Improve the ASYNC “Frame end code” until maximum two characters (“don’t care” is available).
Therefore, users can divide the frame by CR(6Dh) or LF(0Ah), and add the time stamp for 1 character by specifying “don’t care”.
Improve the processing speed of RS-485 driver control when RS-530 driver is “Auto”.
Correct the bug of processing the communication condition for Auto-configuration.
Correct the bug of freezing when stopping the Auto-configuration.
Adjust the timing of I2C stop condition when using OP-SB85.
Correct the bug of display massage.

Bug Fixes

LE-8200 released