PRODUCT
Expansion kit for LAN/PoE (2ch) measurement (EtherCAT supported)
(For LE-8600X/LE-8500X series)
(For LE-8600X/LE-8500X series)
SB-FE2
Specification
| Applicable analyzers | LE-8600X series, LE-8500X series |
|---|---|
| Measurement interface | RJ-45 connector Ports A, B, C, D: 100BASE-TX/10BASE-T Through connection tap specification between ports A-B and C-D※1 |
| Online monitor function | 2-channel simultaneous recording and real-time display of LAN frames flowing between ports A-B and C-D |
| Suitable frame size | 60 bytes to 9KB |
| Time stamp | The reception time is added as time stamp data for each received frame Resolution: 8n seconds/1u seconds/10u seconds can be selected |
| Detailed translation | Target protocols: IPv4, ARP, ICMP, TCP, UDP, DHCP, EtherCAT, IPv6, ICMPv6 |
| pcap conversion | Measurement data can be converted to a pcapng format file and saved |
| csv conversion | Measurement data can be output as a csv format file |
| txt conversion | Measured data can be output as a txt file |
| Filter Function | Monitor only specific frames that match one or two specified conditions |
| Filter Conditions | Layer 2 type (IPv4, ARP, NetBios, IPv6, EtherCAT, type number specification), Layer 2 source address, Layer 2 destination address, IPv4 protocol (ICMP, IGMP, TCP, UDP, protocol number specification), Source port number/address, destination port number/address, subnet mask |
| Trigger Function | The operation can be specified for each of the three types of triggers (external signal trigger, frame detection trigger, FCS error trigger). In addition, it is possible to output an external TTL signal when a trigger occurs, and sound a buzzer when the monitor automatically stops. |
| External Trigger | Condition: When the external TTL signal changes to L level Action: Automatically stop monitoring or save the preceding and succeeding data to a file (trigger save) |
| Frame Detection Trigger | Condition: Layer 2 type (IPv4, ARP, NetBios, IPv6, EtherCAT, type number specified), Layer 2 source address, Layer 2 destination address, IPv4 protocol (ICMP, IGMP, TCP, UDP, protocol number specified), source port number/address, destination port number/address, subnet mask Action: Automatically stop monitoring or count the number of matches |
| FCS Error Trigger | Condition: When an FCS error packet is detected, Action: Automatically stop monitoring or save the preceding and succeeding data to a file (trigger save) |
| Search Function | Search and count only specific frames that match the specified conditions from the measured data |
| Search Conditions | Error occurrence frame, specified frame size, measurement port, and specific frame that can be specified in the same way as the trigger condition |
| Delay time measurement function | Tx between specified ports or Rx, measures the time difference between the two reception timings in µsecond units, and displays the current, maximum, minimum, and average values as delay times |
| Statistical analysis function | Two frame counter values are collected at specified intervals (2 to 240 seconds, 1 to 240 minutes) and displayed as graphs, and all frame counter values and data rates can be displayed in real time |
| PoE measurement function | Supports PoE/PoE+/PoE++ (IEEE802.3af/at/bt), and can measure simultaneously with LAN frames Recording interval: 1ms to 1s, Maximum number of records: 16.77 million, Voltage measurement range: 0 to 60V (Accuracy: ± 1% F.S.), Current measurement range: 0 to ± 900mA (Accuracy: ± 1% F.S.) |
| Packet differential measurement function | Compares received packets between specified ports and displays the differences |
| Other functions | Auto-save function, automatic backup function, time-specified automatic RUN/STOP function, file management function, printout function |
| Components | Interface sub board x 1, LAN cables x 2, external signal output cable (LE-4TG) x 1, quick start guide x 1, warranty card x 1 |
*1: The connection remains even when the power is off.