| SI-60/SI-60-E | SI-65/SI-65-E | |
|---|---|---|
| Conversion Function | LAN <-> RS-232C | LAN <-> RS-422/485 |
| LAN Interface | RJ45 Connector, 10Base-T/100Base-TX
Auto-detection, Ethernet: IEEE 802.3 |
|
| LAN Protocols | TCP/IP, UDP/IP, ARP, ICMP, SNMP, TFTP, Telnet, DHCP, BOOTP, HTTP, Auto IP | |
| Serial Interface | RS-232C, DSUB25pin
(Female), DTE/DCE Swichable |
RS-422/485, 6 pole terminal block (Press-to-screw pitch type), Compatible wire AWG24-14/2.5mm2 |
| Serial Signal | SD, RD, RTS, CTS, DSR / DTR (*1) | SD, RD or SD/RD |
| Synchronous Method | Asynchronous | |
| Communication Speed | 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115.2K, 230.4K, 460K(*2), 920K(*2) (bps) |
|
| Data Frame Structure | Data bits [7 or 8] + Parity [Even / Odd / none] + Stop bits [1 / 2] | |
| Flow Control | XON/XOFF, RTS/CTS | |
| RS-485 Line Monitor | Monitors a non-communications status of the RS-485 line. (*3) | |
| RS-485 Driver Auto-Control |
Controls the RS-485 driver as active only when sending. (*4) | |
| Initial Setup, Management | Web server, serial login, telnet login, SNMP | |
| Sample Software | Attaches the sending/receiving program for Windows 98/Me/2000/NT/XP/Vista (including source code). | |
| Firmware | Writes into the built-in flash memory by FTP or the serial communications. | |
| LED Display | LAN connection status, RS-232C line status |
LAN connection status. RS-485 line status |
| Power Supply | Use the included AC adapter (AC100V +15 to -15%), or
supplies DC 5 to 12V from 9 pin of the DSUB connector.
(*5) Wide Input AC adapter is included to SI-60-E. |
Use the included AC adapter (AC100V +15 to -15%), or
supplies DC 5 to 12V from 6 pin of the terminal block.
(*5) Wide Input AC adapter is included to SI-65-E. |
| Operating Temperature/Humidity | -10 to 50 degrees centigrade (*5), 5 to 95%RH | |
| Dimension /Weight | 65 x 95 x 24 mm (W x D x H), Approx. 200g | 65 x 90 x 24 mm (W x D x H), Approx. 200g |
| Accessories | AC adapter, Utility CD-ROM, Instruction manual, Warranty | |
| *1: | 6 pin and 20 pin (DSR and DTR) of the DSUB connector are connected inside of the converter. |
| Also, CP2 of XPortTM allows you to confirm the logic state. | |
| *2: | SI-60 cannot have speed at 460.8 or 921.6Kbps. To use SI-60F/SI-65 5 at 460.8 or 921.6Kbps, a built-in XPort is required to set to a high performance mode. For more information about this mod |
| *3: | The half duplex RS-485 communications is requested to send the data when any devices do |
| not send data into the RS-485 line. The line monitor function of SI-65 detects that any devices do | |
| not send any data continuously over the timer time specified by SW-A. Then, to communicate with | |
| CP3 of XPortTM, it decreases the loads of the communications control coming from LAN. | |
| *4: | In the half duplex RS-485 communications, you must set the RS-485 driver IC to active only when |
| sending data. The driver auto-control function of SI-65 immediately makes the RS-485 driver IC | |
| active at the head of the sending data. Then, the function automatically makes the driver non-active | |
| after timer time specified by SW-A passes from the end of the sending data string. | |
| *5: | If the power voltage, which is supplied from the DSUB connector (SI-60) or terminal block (SI-65), |
| is more than DC 10V, operating temperature becomes -10 to 40 degrees centigrade. |